Switch Glossary of Terms

9 April 2010

Here is a handy glossary of terms for the switch industry, including explanations of switch abbreviations.

Actuator:  The mechanical interface between the basic switch contacts and the means of operation, such as the operator’s finger.

Actuation Force:  The required force to change a circuit’s electrical state.

Alternate Action Switch:  A  pushbutton  style switch where the change of the electrical state is maintained between actuations.

Ampere:  A unit of electrical current flow.

Base (Housing):  The main member to which the conducting parts or insulator unit are attached. It may also have parts of the operating or control mechanism attached.

Bounce:  Rebounding of moving contact against fixed contact during transfer.

Break:  Interruption of a circuit. Double-break occurs when a single mechanism interrupts two contacts simultaneously.

Break Before Make:  The term given to a double throw circuit where the first circuit is opened before the second circuit is closed.

Capacity:  Usually refers to the current handling capability of a switch.

Chatter:  Rapid opening and closing of contacts, usually exhibited during extreme vibration and/or shock.

Clearance (Spacing):  Distance through air between electrically live parts of opposite polarity or to ground.

Contact:  The contact is a conducting part designed to be united by pressure to another conducting part for the purpose of carrying current.

Contact Bounce:  Oscillation of the movable contact upon closure of the circuit.

Contact Gap:  The minimum distance between the fixed and moveable contacts.

Contact Resistance:  The resistance of current flow across closed contacts.

Dead-break:  Open circuit condition, usually caused when slowly actuating  snap-action switches. Results from low contact pressure or contact lift-off.

Detent:  Feature that indicates actuation point has been reached. Can also be referred to as tactile feel.

Dielectric Strength:  The ability of an insulating material to resist voltage from arcing across its surface.

Differential:  Distance between trip point (or force) and reset point (or force).

Double-break:  A mechanism that breaks the circuit at two points simultaneously by means of a “shorting bar” like device.

Double-throw:  Contact arrangement that alternately transfers normally open and normally closed circuits.

Dust-tight:  Will withstand sand and dust contamination.

Electrical Life:  Expected cycle life when switch is operated at full electrical load.

Free Position:  Point at which plunger exists in the un-operated condition.

Insulation Resistance:  The resistance to current flow of the insulating materials between contacts.

Lever Actuator:  A device, hinged or spring type, applied to a basic switch to facilitate its application.

Make Before Break:  The term given to a double throw circuit when the second circuit is closed before the first circuit is opened.

Momentary Action Switch:  A circuit is continuously closed or opened only when force is applied. The electrical state returns to its normal position when the force is removed.

Normally Closed:  A circuit is closed in the normal switch position.

Normally Open:  A circuit is open in the normal switch position.

Operating Point:  Point at which contacts transfer. Usually measured from the switch mounting holes.

Over Travel:  The distance an actuator travels after the circuit is closed.

Pole:  The term to denote a completely separate circuit, which passes through a switch at one time.

Pre-travel:  The movement of the actuator prior to closing the circuit. Sometimes identical to “Travel to Make”.

Reset Point:  Point at which contact resumes normal position. Single-Break: Mechanism that transfers one contact.

Single Throw Switch:  The circuit can be opened or closed by moving the switch blade into or out of one set of contacts only.

Snap Action:  The abrupt transfer of contacts from one position to another. This action is relatively independent of the speed of actuator travel.

Splash-proof:  Will withstand heavy rain or stream of water.

Switch:  A device for making, breaking, or changing the connections in an electric circuit.

Throw:  The term denotes the number of positions in which a given pole is closed.

Travel to Make:  The distance parallel to the designated direction of the actuator movement at which point a circuit is closed.

Watertight:  Will withstand submersion to various depths depending on specification level.

Wiping Action:  Lateral travel of movable contact over fixed contact while pressure between the two contacts exists. Occurs during plunger travel. This action helps clean the contacts of contamination.

Switch Abbreviations

N.C.:  Normally Closed circuit

N.O.:  Normally Open circuit

SPST:  Single Pole Single Throw

SPDT:  Single Pole Double Throw

DPST:  Double Pole Single Throw

DPDT:  Double Pole Double Throw

MBB:  Make Before Break

BBM:  Break Before Make

The post Switch Glossary of Terms appeared first on E-Switch, Inc..

by Jeremy Biggs • 5 November 2026
Piezo Buzzer – Turning Vibration Into Sound
by Jeremy Biggs • 20 May 2026
Looking for a Switch - Download E-Switch New Product Matrix
by Jeremy Biggs • 8 May 2026
State of the Art, Inc. Introduces AEC-Q200 Qualified Thick Film Chip Resistors
by Jeremy Biggs • 1 May 2026
E-Switch 6mm x 6mm Tact Switch Family
by Jeremy Biggs • 14 April 2026
Sealed Speaker Enclosure Design for Small Speakers (Practical QTC = 0.707 Guide)
Promotional banner for PV Series anti-vandal switches, with red background and metal push buttons
by Jeremy Biggs • 14 April 2026
Explore durable anti-vandal pushbutton switches with IP65/IP67 ratings. Contact us for details on our extensive range today!
by Anthony Varriano • 17 January 2023
Explore E-Switch's miniature switches for handheld & wearable tech. Request brochures & samples to learn more about our solutions.
by Erin • 12 January 2023
Dayton, OH, USA – PUI Audio is pleased to announce the addition of Reptronics to their growing list of sales representatives. Reptronics is a manufacturer’s representative company operating within the United Kingdom and Ireland, and currently work with several global manufacturers of high-quality electrical components. PUI Audio selected Reptronics to join their global sales network […]
by Erin • 16 December 2022
Reptronics Ltd supports Principals in selling electronic components in the UK & Ireland. Contact us to enhance your product reach.
by Anthony Varriano • 8 December 2022
When snow falls, don’t get mad. Be glad you have the switches for moving snow and ice this winter. The post Switches for Moving Snow and Ice appeared first on E-Switch, Inc..